Product Data Sheet Show all documents
EVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT

EVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT

Solvent-based, full-bodied black bitumen paint for metal protection

EVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT is a solvent-based, full-bodied black bituminous paint. When dry, the product forms an odourless and taint-free black film suitable for metal protection as well as overcoating wood and felt.

  • Fast drying.
  • For use on most common building surfaces.
Type of SolventWhite SpiritFlashpointca. 40°CFilm Thickness Per Coat @ 11m2 / Ltr Wet – 0.1mm Dry – 0.05mmChemical And Water Resistance Resistant to: most salt solutions, dilute acids and alkalis, water and alcohol. Not resistant to: oils, solvents and some detergent solutionsService Temps-20°C to +50°C
Ask for a quote
Product Data Sheet Show all documents

Usage

EVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT provides an effective waterproof, weatherproof, corrosion-resistant protective coating. It is resistant to low concentrations of alkalis and acids and can withstand prolonged oxidation. It is suitable for application to a wide variety of materials including iron, steel, lead, zinc, aluminium, asbestos-cement, concrete, stone, wood, felt and brick and is mainly used for:
  • Metal protection - corrugated iron sheets, fire escapes, stairways, ladders, storage tanks, gutters, downpipes, fences, railings, gates etc.
  • As a protective coating for concrete structures, stone, brick, concrete screeds and sand/cement surfaces.
  • Overcoating felt/wood.
 

Advantages

  • Fast drying.
  • For use on most common building surfaces.
Type of SolventWhite SpiritFlashpointca. 40°CFilm Thickness Per Coat @ 11m2 / Ltr Wet – 0.1mm Dry – 0.05mmChemical And Water Resistance Resistant to: most salt solutions, dilute acids and alkalis, water and alcohol. Not resistant to: oils, solvents and some detergent solutionsService Temps-20°C to +50°C

Packaging

1L, 2.5L, 5L and 25L tins

Colour

Black

Product Details

Product Information

Chemical Base

Solvent-based bitumen

Shelf Life

24 months from date of manufacture in tightly sealed, undamaged containers.

Storage Conditions

EVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT contains a flammable solvent, and all normal precautions against fire must be taken during both storage and use. Store in original container in cool (5°C - 25°C) dry conditions. Keep away from sources of ignition.

Density

ca. 0.9 g/cm3 at 20°C

Viscosity

700-1200 cP
Technical Information

Service Temperature

-20°C to +50°C

Application

Application Information

Ambient Air Temperature

5°C - 40°C. Surfaces must be free from ice and water.

Drying time

4-6 hours depending on drying conditions
Application steps

SUBSTRATE PREPARATION

As with all surface coatings, preparation of the surface is of great importance and will influence the degree of adhesion obtained and the life of the coating. All surfaces must be sound, stable and thoroughly clean and dry. Metal surfaces should be wire-brushed to remove rust. Where long-term protection is required an initial treatment of a rust-inhibitive product such as red lead or zinc phosphate should be used. Loose or blistered paint should be removed, as should tar-based paint systems. New galvanised surfaces should be roughened with a wire brush or treated with a proprietary etch primer. Porous surfaces should be primed with Black Jack® Bitumen & Flashing Primer.

APPLICATION

EVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT is ready for use and should not be thinned. Stir thoroughly before use. Apply by brush or spray.

A minimum of two coats of EVERBUILD® BLACK JACK® 901 BLACK BITUMEN PAINT should be applied. The first coat should be allowed to dry (normally 2-4 hours depending on weather conditions) before the second coat is applied.

CLEANING OF TOOLS

Tools may be cleaned by using white spirit. Any spillage should be wiped off surfaces before the bitumen paint has set.

 

Documents