
Sika® Armorex L2 High Flow
Sika® Armorex® L2 High Flow is a one part, high flow, rapid strength cementitious grout.
- High strength
- Shrinkage compensated
- High flowability retention
- Durable
- Non metallic
- Impressive track record
- Quality assured factory blend
- Chloride free
- >40 N/mm2 in 24 hours
Usage
- For precision, high performance, grouting underneath machine bases, structural steelwork, etc
- For grouting precast concrete units and anchor bars
- Repairing concrete structures
- Filling voids
- For grouting thicknesses between 10 -100 mm
- Steel reinforcement anchoring
Advantages
- High strength
- Shrinkage compensated
- High flowability retention
- Durable
- Non metallic
- Impressive track record
- Quality assured factory blend
- Chloride free
- >40 N/mm2 in 24 hours
Packaging
25kg bags
Colour
Grey powder
Product Details
APPROVALS / STANDARDS
Meets the requirements of BS EN 1504-6
Chemical Base
Cement, selected fillers and aggregates, special additives
Shelf Life
9 months
Storage Conditions
Store properly in dry conditions in undamaged and unopened original sealed packaging
Density
~ 2180 kg/m3 (wet density)
Maximum Grain Size
1.0 mm
Compressive Strength
Compressive Strength tested to BS 1881:Part 116:1983 - ambient temperature +20°C
1 day | 3 days | 7 days | 28 days | |
Pourable | ~42MPa | ~56MPa | ~68MPa | ~77MPa |
Flowable | ~40MPa | ~54MPa | ~65MPa | ~74MPa |
Fluid | ~25MPa | ~45MPa | ~60MPa | ~70MPa |
Modulus of Elasticity in Compression
~29 GPa
Flexural Strength
7 days | 28 days |
~8MPa | ~10.5MPa |
Ambient temperature +20°C
Tensile Strength
7 days | 28 days |
~2MPa | ~3.5MPa |
Ambient temperature +20°C
Pull-Out Resistance
Pull out (Dry) | Displacement < 0.6mm at load of 75KN (BS EN 1504-6) |
Pull out (Wet) | Displacement < 0.6mm at load of 75KN (BS EN 1504 -6) |
Ultimate Anchorage Bond Strength
6.7 MPa
Electrical Resistivity
~4.5 (K.ohm.cm) | (Wenner Test) |
Application
Layer Thickness
10 mm min. / 100mm max
Flowability
Flow cone test
5°C | 33 seconds |
20°C | 33 seconds |
Efflux times at fluid consistency
Ambient Air Temperature
+5°C min. / +25°C max.
Substrate Temperature
+5°C min. / +25°C max.
Yield
25 kg yields 13.5 litres of fluid grout
1850 kg yields 1m3 of fluid grout
MIXING
Measure the appropriate amount of water to achieve the desired grout consistency given in the table below. Heat water if necessary to achieve a temperature between 15-20oC.
Water addition per 25kg bag
Pourable consistency | 3.75 litres |
Flowable consistency | 4.25 litres |
Fluid consistency | 4.75 litres |
Place the water into a forced action grout mixer or in a clean drum. Slowly add complete bag of Sika® Armorex® L2 High Flow into the water and continuously mix for 3 minutes in mixer to achieve a uniform and lump free consistency. Alternatively use a slow speed drill (200-500 rpm) and helical mixer. Dependent on the desired consistency and flow properties, the mixing ratio can be adjusted.
APPLICATION
Immediately after mixing, pour the mixed grout into the header box/hopper ensuring continuous grout flow during the complete grouting operation to avoid trapping air. Use steel banding or chains to assist flow where necessary. For large volume placement, grout pumps are recommended.
CURING TREATMENT
After the grout has initially hardened, remove formwork and trim edges while concrete is ‘green’. Cure all exposed grout surfaces using Sikafloor® ProSeal. In cold weather apply heat blankets to maintain a constant temperature.
CLEANING OF TOOLS
Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed.