Product Data Sheet Show all documents
Sikafloor® ProSeal-90

Sikafloor® ProSeal-90

CURING AND SEALING COMPOUND FOR CONCRETE FLOORS

Sikafloor® ProSeal-90 is a solvent based, clear acrylic resin polymer solution used to cure, harden and seal fresh or hardened concrete.

  • Excellent moisture retention
  • Curing efficiency 90% (ASTM C-156)
  • Good adhesion to old and new concrete
  • Quick drying
  • Helps control dusting for both new and existing concrete floor surfaces
  • Effectively cures and seals concrete surfaces in a single, economic operation
  • Non yellowing
  • Easy application by spray or roller
Ask for a quote
Product Data Sheet Show all documents

Usage

  • Sikafloor® ProSeal-90 is used for optimum curing and sealing of fresh concrete floors and structures
  • Curing compound in order to limit surface drying and cracking
  • Provides curing and sealing for Sikafloor® dry shake hardeners
  • Anti-dust treatment and improvement of the abrasion resistance of existing concrete surfaces
  • Suitable for exterior and interior application
 

Advantages

  • Excellent moisture retention
  • Curing efficiency 90% (ASTM C-156)
  • Good adhesion to old and new concrete
  • Quick drying
  • Helps control dusting for both new and existing concrete floor surfaces
  • Effectively cures and seals concrete surfaces in a single, economic operation
  • Non yellowing
  • Easy application by spray or roller

Packaging

25 l metal pails and 200 l metal drums.

Colour

Clear Liquid

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

Conforms to the requirements of ASTM C-309 for curing liquids type 1, ASTM C-156 for water retention, and ASTM D-4060 for improvement of abrasion resistance

Conforms to the requirements of EN 13813 SR – B 1.5

Test report from GEOCISA Ref. P-02/01463-A Rev. 1 dated August 7, 2002 Abrasion resistance according to UNE 48.250-92 (ASTM D-4060)

Test report from GEOCISA Ref. P-02/01463 dated June 7th, 2002 Water retention according to ASTM C-156

Epoxy textured roller and seal coat according to EN 13813:2002, DoP 01 08 03 04 005 0 000008 1049 and provided with the CE-mark
Product Information

Chemical Base

Solvent based acrylic resin.

Shelf Life

12 months from date of production, if stored properly in original, unopened and undamaged sealed containers, in dry conditions at temperatures between +5 °C and +25 °C.

Storage Conditions

Protect from frost.

Density

~ 0.9 kg/I (at +20 °C)

Solid content by weight

~18% (by weight)

Application

Application Information

Ambient Air Temperature

+10 °C min. / +30 °C max.

Relative Air Humidity

80% r.h. max.

Dew Point

Beware of condensation!

The substrate and uncured floor must be at least 3 °C above dew point to reduce the risk of condensation or blooming on the floor finish.

Substrate Temperature

+10 °C min. / +30 °C max.

Curing Time

Applied Product ready for use

Substrate temperature

+10 °C

+10 °C

+30 °C

Foot traffic

~ 4 hours

~ 3 hours

~ 2 hours

Full cure

~ 24 hours

~ 20 hours

~ 16 hours

Note: Times are approximate and will be affected by changing ambient and substrate conditions.

Waiting Time / Overcoating

Allow previous coats to become tack free before applying additional coats.

Substrate Temperature

+10 °C

+20 °C

+30 °C

Time

~ 60 minutes

~ 25 minutes

~ 20 minutes

Times are approximate and will be affected by changing substrate and ambient conditions, particularly temperature and relative humidity.
Consumption

Consumption

0.1 - 0.25 l/m2/coat. (4 - 10 m2/l/coat)

This figure is theoretical and does not include for any additional material required due to surface porosity, surface profile, variations in level and wastage, etc.
Application steps

MIXING

Sikafloor® ProSeal-90 is supplied ready for use. Stir thoroughly before use for a minimum of 2 minutes using a low speed electric stirrer (~300 rpm).

APPLICATION

For fresh concrete, apply immediately after finishing techniques have been completed.
Apply in a continuous even film by low-pressure spray unit. The suitability of spraying equipment must be confirmed by trials.
Application also possible by brush or roller.
To achieve the highest visual aesthetics and performance, a second coat is recommended.
Wait for first coat to dry tack free before applying a second coat.

CLEANING OF TOOLS

Clean all tools and application equipment with Sika® Thinner C immediately after use. Hardened / cured material can only be removed mechanically.

CLEANING

To maintain the appearance of the floor after application, Sikafloor® ProSeal-90 must have all spillages removed immediately and must be regularly cleaned using rotary brushes, mechanical scrubbers, scrubber dryers, high pressure washers, wash and vacuum techniques, etc., using suitable detergents and waxes.

Documents