Sikafloor® MultiDur WS-10
Epoxy, low-VOC emission, waterborne, smooth floor coating system
Sikafloor® MultiDur WS-10 is a low VOC waterborne, epoxy resin, smooth floor coating system.
- Low VOC emissions
- Low Airborne Molecular Contaminants (AMC) emissions
- Low VOC content
- Low odour
- Seamless
- Good mechanical resistance
- Good resistance to specific chemicals
- Easy application
- Good water vapour permeability
- Low maintenance
System Structure
Usage
Sikafloor® MultiDur WS-10 is used in industrial buildings such as:- Storage areas
- Assembly halls
- Logistics facilities and warehouses
- Manufacturing facilities and workshops
- The System may only be used by experienced professionals.
Advantages
- Low VOC emissions
- Low Airborne Molecular Contaminants (AMC) emissions
- Low VOC content
- Low odour
- Seamless
- Good mechanical resistance
- Good resistance to specific chemicals
- Easy application
- Good water vapour permeability
- Low maintenance
Colour
Cured system colour | Available in various colour shades |
Appearance
Smooth, semi-gloss finish
System Details
APPROVALS / STANDARDS
-
Fire Testing DIN EN 13501-1, Sikafloor®-MultiDur WS-10, Hoch, Report No KB-Hoch-
System Structure
Sikafloor® MultiDur WS-10
| Layer | Product | |
| 1. | Primer | Sikafloor®-2540 W + 5 % water by weight |
| 2. | Top coat | Sikafloor®-2540 W |
Composition
Water-based epoxy
Nominal thickness
0.2-0.3 mm
Abrasion Resistance
Cured 14 days at +23 °C | 63 mg (CS 10 / 1000 g / 1000 cycles) |
Tensile adhesion strength
≥ 1.5 MPa | (EN 1542) |
Reaction to Fire
Class Bfl-s1 | (EN 13501-1) |
Chemical Resistance
Laboratory-defined resistance to many individual chemicals. Before proceeding, contact Sika Technical Service for specific information.
Application
Ambient Air Temperature
Maximum | +30 °C |
Minimum | +10 °C |
Relative Air Humidity
Maximum | 75 % r.h. |
Dew Point
Refer to the individual Product Data Sheet.
Substrate Temperature
Maximum | +30 °C |
Minimum | +10 °C |
Substrate Moisture Content
Refer to the individual Product Data Sheet.
Waiting Time / Overcoating
Before applying Sikafloor®-2540 W on Sikafloor®-2540 W allow:
Substrate temperature | Minimum | Maximum |
+10 °C | 48 hours | 7 days |
+20 °C | 20 hours | 6 days |
+30 °C | 10 hours | 3 days |
Note: Times are approximate and will be affected by changing ambient conditions, particularly temperature and relative humidity.
If relative air humidity is ≥ 75 % the waiting time is increased by at least 24 hours.
Applied Product Ready for Use
Temperature | Foot traffic | Light traffic | Full cure |
+10 °C | 48 hours | 5 days | 10 days |
+20 °C | 20 hours | 3 days | 7 days |
+30 °C | 10 hours | 2 days | 5 days |
Note: Times apply when the last layer of the system has been applied. Times are affected by changing ambient conditions, particularly temperature and relative humidity.
Consumption
| Layer | Product | Consumption |
| Primer | Sikafloor®-2540 W + 5 % water by weight | 1 × 0.2–0.3 kg/m² |
| Top coat | Sikafloor®-2540 W | 1–2 × 0.2–0.3 kg/m² per layer |
Note: Consumption data is theoretical and does not allow for any additional material due to surface porosity, surface profile, variations in level, wastage or any other variations. Apply the Product to a test area to calculate the exact consumption for the specific substrate conditions and proposed application equipment.