Product Data Sheet Show all documents

EVERBUILD® 502 Weatherproof Wood Adhesive

A high quality, D3, resin based wood adhesive.

Can be used internally and externally and provides a high strength, impact resistance bond that is usually stronger than the wood itself. Ideal for all general woodworking and joinery uses, furniture assembly and household DIY use. Dries clear. Fast cure, initial set in just 10 minutes.

• Excellent rate of bond strength development.
• High degree of water resistance. D3 Classification- joints may be subject to short term water contact or exposure to high humidity.
• Interior/exterior use.
• Low timber staining characteristics - will not stain.
• Creep Resistant - Conforms to EN14256 Resistance to static load.
• Dries clear - contains no inert fillers.
• Water based - environmentally friendly/easy clean up.
• Suitable for radio frequency cure.                                                                                                      Specific Data Viscosity @ 23°C Brookfield RTV 5/20 7000-15000 cP pH 2.0-4.0                                                                                                                           PRODUCT EN204 D3/3 BSEN 14256 Everbuild A/P Wood Adhesive Ave 2.17 N/mm²19.2 daysSpecification≥2.0 N/mm² ≥ 14 days
Find a Technical Advisor
Product Data Sheet Show all documents

Usage

As a weatherproof/creep resistant wood adhesive, internally and externally.

Advantages

• Excellent rate of bond strength development.
• High degree of water resistance. D3 Classification- joints may be subject to short term water contact or exposure to high humidity.
• Interior/exterior use.
• Low timber staining characteristics - will not stain.
• Creep Resistant - Conforms to EN14256 Resistance to static load.
• Dries clear - contains no inert fillers.
• Water based - environmentally friendly/easy clean up.
• Suitable for radio frequency cure.                                                                                                      Specific Data Viscosity @ 23°C Brookfield RTV 5/20 7000-15000 cP pH 2.0-4.0                                                                                                                           PRODUCT EN204 D3/3 BSEN 14256 Everbuild A/P Wood Adhesive Ave 2.17 N/mm²19.2 daysSpecification≥2.0 N/mm² ≥ 14 days

Packaging

various

Colour

Dries clear

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

BS EN204 D3

BS 14256

Product Information

Shelf Life

12 months

Storage Conditions

To ensure safe storage of EVERBUILD® 502 Weatherproof Wood Adhesive, containers should be well sealed to prevent evaporation of water and the formation of skin on the surface. The emulsion must be stored at a temperature above freezing. A temperature of 5-25°C for not more than six months is recommended. Higher temperatures will affect quality and cause the formation of crusts and skins, especially if the containers are not tightly closed or subjected to direct sunlight for long periods. During storage, slight separation may occur. (thin layer above thicker layer). This is an esthetic rather than technical problem. In this case, shake well before applying. If these conditions cannot be met, please refer to our Technical Service Department who will advise on storage stability.

Density

1.0-1.2 g/cm3

Solid content by weight

46-49%
Technical Information

Thermal Resistance

Stable (4 week @ 50°C)

Application

Application steps

APPLICATION INSTRUCTIONS

Apply adhesive thinly to both surfaces. Do not over apply as this will slow down cure. Clamp surfaces together until adhesive dries (off in 1-2 hours: full strength 8 hours). Support until fully cured (8 hours at 20°C). When fitting dowels, the adhesive should be applied to the holes.
• Suitable for radio frequency curing.

SUBSTRATE PREPARATION

All surfaces must be clean, dry and free from grease.

Documents