Sikafloor®-155 WN
Water-based epoxy primer
Sikafloor®-155 WN is a water-based epoxy resin primer.
- Easy application
- Low odour
- Low viscosity
- Good penetration
- Good bond strength
Usage
Sikafloor®-155 WN is used on the following substrates:- Concrete
- Cementitious screeds
- Epoxy mortars
- Normal to highly absorbent surfaces and substrates
- The Product may only be used for interior applications.
Advantages
- Easy application
- Low odour
- Low viscosity
- Good penetration
- Good bond strength
Packaging
Container Part A | 7.5 kg and 22.5 kg |
Container Part B | 2.5 kg and 7.5 kg |
Container Part A + Part B | 10 kg and 30 kg |
Refer to the current price list for available packaging variations.
Colour
Part A | Coloured paste |
Part B | light yellow-translucent liquid |
Cured colour | Oxide red (~ RAL 3009) |
Product Details
ENVIRONMENTAL INFORMATION
Contributes towards satisfying Indoor Environmental Quality (EQ) Credit: Low-Emitting Materials under LEED® v4
Contributes towards satisfying Materials and Resources (MR) Credit: Building product disclosure and optimization — Environmental Product Declarations under LEED® v4
Chemical Base
Water-based epoxy
Shelf Life
12 months from date of production
Storage Conditions
The Product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +30 °C. Always refer to packaging.
Refer to the current Safety Data Sheet for information on safe handling and storage.
Density
Part A | 1.6 kg /l |
Part B | 1.1 kg /l |
Mixed Product | 1.4 kg /l |
Solid content by mass
70 %
Solid content by volume
56 %
Tensile adhesion strength
> 1.5 N/mm² (failure in concrete) | (EN 1542) |
Application
Mixing Ratio
Part A : Part B (by weight) | 75 : 25 |
Layer Thickness
110-180 µm per layer (dry film thickness)
Product Temperature
Maximum | +30 °C |
Minimum | +10 °C |
Ambient Air Temperature
Maximum | +35 °C |
Minimum | +10 °C |
Relative Air Humidity
Maximum | 80 % r.h. |
Dew Point
Beware of condensation. The substrate and uncured applied product must be at least +3 °C above dew point to reduce the risk of condensation or blooming on the surface of the applied product. Low temperatures and high humidity conditions increase the probability of blooming.
Substrate Temperature
Maximum | +35 °C |
Minimum | +10 °C |
Substrate Moisture Content
Substrate | Test method | Moisture content |
Cementitious substrates | Calcium carbide method (CM method) | ≤ 4 % |
No rising moisture (ASTM D4263, polyethylene sheet)
Pot Life
+10 °C | 180 minutes |
+20 °C | 90 minutes |
+30 °C | 45 minutes |
Waiting Time / Overcoating
Before applying Sikafloor®-81 EpoCem® or Sikafloor®-82 EpoCem® onto Sikafloor®-155 WN allow:
Substrate temperature | Minimum | Maximum |
+10 °C | 12 hours | 72 hours |
+20 °C | 6 hours | 48 hours |
+30 °C | 4 hours | 24 hours |
Apply subsequent coats only to tack free primer.
Note: Times are approximate and will be affected by changing ambient conditions, particularly temperature and relative humidity.
Consumption
0.3–0.5 kg/m2 per coat
Dilute the first coat with water 10 % by weight. The second coat is applied undiluted.
Note: Consumption data is theoretical and does not allow for any additional material due to surface porosity, surface profile, variations in level, wastage or any other variations. Apply the Product to a test area to calculate the exact consumption for the specific substrate conditions and proposed application equipment.
EQUIPMENT
SUBSTRATE PREPARATION
Abrasive blast cleaning equipment
Planing machine
Scarifying machine
MIXING
Electric double-paddle mixer (>700 W, 300 to 400 rpm)
Electric single-paddle mixer (300 to 400 rpm)
Scraper
Clean mixing containers
APPLICATION
Short-pile nylon roller
SUBSTRATE QUALITY
Cementitious substrates must be structurally sound and of sufficient compressive strength (minimum 25 N/mm2) with a minimum tensile strength of 1.5 N/mm2.
Substrates must be clean, dry and free of contaminants such as dirt, oil, grease, coatings, laitance, surface treatments and loose friable material.
Use industrial vacuuming equipment to remove all dust, loose and friable material from the application surface before applying the Product.
TREATMENT OF JOINTS AND CRACKS
Construction joints and existing static surface cracks in substrate require pre-treating before full layer application. Use Sikadur® or Sikafloor® resins.
SUBSTRATE PREPARATION
MECHANICAL SUBSTRATE PREPARATION
IMPORTANT
Surface defects due to voids in the substrate
Voids and blow holes in the substrate will weaken the surface and damage the covering Product if not repaired during the preparation process.
- Fully expose blow holes and voids during surface preparation to identify the required repairs.
- Remove weak cementitious substrates.
- Prepare cementitious substrates mechanically using abrasive blast cleaning, abrasive planing or scarifying equipment to remove cement laitance.
- Before applying thin layer resins, remove high spots by grinding.
- Use industrial vacuuming equipment to remove all dust, loose and friable material from the application surface before applying the Product.
- Use products from the Sikafloor®, Sikadur® and Sikagard® range of materials to level the surface or fill cracks, blow holes and voids.
Contact Sika® Technical Services for additional information on products for levelling and repairing defects.
SUBSTRATE PREPARATION OF NON-CEMENTITIOUS SUBSTRATES
For information on substrate preparation of non-cementitious substrates, contact Sika® Technical Services.
MIXING
FIRST COAT
- Mix Part A (resin) until the coloured pigment is dispersed and a uniform colour is achieved.
- Add Part B (hardener) to Part A.
- IMPORTANT Do not mix excessively. Mix Part A + B continuously for ~2 minutes while adding 10 % water until a uniformly coloured mix is achieved.
- To ensure thorough mixing, pour materials into another container and mix again to achieve a smooth and uniform mix.
- During the final mixing stage, scrape down the sides and bottom of the mixing container with a flat or straight edge trowel at least once to ensure complete mixing.
SECOND COAT
- Mix Part A (resin) until the coloured pigment is dispersed and a uniform colour is achieved.
- Add Part B (hardener) to Part A.
- IMPORTANT Do not mix excessively. Mix Part A + B continuously for ~2 minutes until a uniformly coloured mix is achieved.
- To ensure thorough mixing, pour materials into another container and mix again to achieve a smooth and uniform mix.
- During the final mixing stage, scrape down the sides and bottom of the mixing container with a flat or straight edge trowel at least once to ensure complete mixing.
APPLICATION
IMPORTANT
Ventilation in confined spaces
Always ensure good ventilation when applying the Product in a confined space.
IMPORTANT
Damaged finish due to heating with fossil fuel heaters
Fossil fuel heaters powered by gas, oil or paraffin produce large quantities of both carbon dioxide and water vapour, which may adversely affect the finish.
- For temporary heating, use only electrically powered warm air blower systems. Do not use gas, oil, paraffin or other fossil fuel heaters.
IMPORTANT
Applying the Product after the end of the pot life
The end of the pot life is not noticeable. Continuing to apply the Product after the end of the pot life may result in the applied material not curing properly.
- Monitor the pot life closely taking into consideration the environmental conditions.
- Discard materials that remain after the pot life has elapsed.
PRIMER COAT APPLICATION
- Pour the mixed Product onto the substrate. Note The consumption is specified in Application Information.
- Apply the Product evenly over the surface with a short pile roller or a squeegee.
- Back-roll the surface in two directions at right angles with a fleece roller. Note Maintain a "wet edge" during application to achieve a seamless finish.
CLEANING OF TOOLS
Clean all tools and application equipment with water immediately after use. Hardened material can only be removed mechanically.