Product Data Sheet Show all documents
Parex® BLANC DU LITTORAL

Parex® BLANC DU LITTORAL

Bright White One Coat Weather Resistant and Decorative Render

A bright white, one-coat weather resistant and decorating render for internal and external vertical masonry and concrete walls.

  • Bright white one-coat finish
  • Only suitable for strong dense substrates
  • Fine-scraped, float smoothed or trowel smoothed textures
Product Data Sheet Show all documents

Usage

As an external render for application onto vertical masonry and concrete walls.  

Advantages

  • Bright white one-coat finish
  • Only suitable for strong dense substrates
  • Fine-scraped, float smoothed or trowel smoothed textures

Packaging

25 kg bags

Colour

FINISHES

  • Fine Scraped
  • Sponge or Float Smoothed*
  • Trowel Smoothed*
  • Spray Textured - from tyrolean style to heavy roughcast effect.

For additional information refer to the data sheet on Textured Mineral Finishes.

*The float/sponge/trowel smoothed finishes may vary in appearance, particularly due to different factors such as the line and level and condition of the substrate or the appearance of a slurry finish caused by over floating the surface. The latter may produce some micro cracking effect on the render surface which may affect the aesthetical appearance but does not affect its durability.

Product Details

Sustainability / Certifications / Approvals

APPROVALS / STANDARDS

EN998-1
Product Information

Chemical Base

Hydraulic mortar containing:
Cement, lime, siliceous and calcareous sands, mineral pigments and specific admixtures.

Shelf Life

12 Months from date of manufacture

Storage Conditions

Dry frost free conditions 

Maximum Grain Size

Granulometry: 0-2.5 mm
Technical Information

Compressive Strength

CS II

Capillary Absorption

W2

Application

Application Information

Mixing Ratio

3.9-4.4 L per 25 kg bag
Consumption

Consumption

Coverage is provided as a guidance only, excludes wastage and will vary subject to substrate conditions and thickness applied.

USES

WEATHERPROOFING COAT

DECORATION

Substrate

Concrete blocks, bricks, etc

Concrete, base coat renders, etc

Scraped

1.0 - 1.1 m2 @ 15 mm/25 kg bag

1.3 - 1.5 m2 @ 10 mm/25 kg bag

Float Smoothed

1.25 - 1.3 m2 @ 15 mm/25 kg bag

1.67 - 1.75 m2 @ 10 mm/25 kg bag

Trowel /Sponged smoothed1.25 - 1.3 m2 @ 15 mm/25 kg bag1.67 - 1.75 m2 @ 10 mm/25 kg bag
Application steps

EQUIPMENT

EQUIPMENT REQUIRED

Application by Machine

SPRAY RENDER MACHINE

CONSTANT MIX AND PUMP MACHINE

Pump Pressure

10-12 bar (water)

15-16 bar/360 water flow L/hr

Pumping Distance/Height

Up to 120 m/60 m approx

Up to 50 m/30 m approx

Powersource

Diesel

Electric, -Based on PFT G4/G5

APPLICATION

  • Refer to and comply with the Substrate Preparation first. 
  • For very severe wind driven rain index locations, high exposure or coastal zones please contact PAREX® for additional guidance as the render thickness may need to be increased and additional surface treatment may be recommended. 

SUITABLE FOR

  • Machine or manual applications.
  • Ensure the product is mixed correctly with the correct water content and do not allow the render to cure too quickly as surface holes in the render could occur

FOR WEATHER PROOFING APPLICATIONS ONTO CONCRETE, CONCRETE BLOCKS, BRICKS, SUBSTRATES (SUBJECT TO SURFACE PREPARATION).

SCRAPED FINISH

  • Apply a level, ruled compact 18 mm thick coat, level the surface with a straight edge, spatula or trowel flat. Allow to dry (3-16 hours) and depending on the substrate and drying conditions, scrape the surface in small circular motions using a scraping tool, removing no more than 3 mm from the surface.
  • This scraping process must remove any slight imperfections and bring the application to the specified finished thickness. Each elevation must be scraped at the same stage, as early scraping will result in a slightly darker shade and later scraping in a lighter shade.The minimum finished thickness after scraping is 15 mm. 
  • After scraping, any dust on the surface should be removed by brushing with a clean soft bristle brush. Always stand back and examine the whole surface for blemishes and unevenness. Errors must be corrected at this stage as rectification later is not practical

SPONGE / FLOAT / TROWEL FINISHES*

  • Apply a level, compact, minimum 15 mm thick coat in 1 or 2 coats. Obtain the finish with a stainless 
    steel floating trowel, wooden, sponge or plastic float

THICKNESS

  • Due to construction variations, the minimum thickness must not be less than 15 mm after the 
     Scraped, Float Smoothed or Trowel/Sponge Smoothed finishes.

RUSTIFICATION/ASHLAR EFFECT

  • It is recommended that a minimum depth of render to the back of the rustification/ashlar cut should be no less than 15mm. To achieve this depth will require the finished thickness of the main render to  be increased to approximately 20 - 25 mm.

FOR DECORATING WATERPROOF CONCRETE AND MASONRY SUBSTRATES I.E. COVERED WITH AN EXISTING SOUND AND  WEATHERPROOF RENDER.

SCRAPED FINISH

  • Apply a level, ruled compact 13 mm thick coat, level the surface with a straight edge, spatula or trowel flat. Allow to dry (3-16) hours and depending on the substrate and drying conditions, scrape the surface in small circular motions using a scraping tool, removing no more than 3 mm from the surface. 
    Then follow the same procedure detailed above.

SPONGE / FLOAT / TROWEL FINISHES*

  • Apply a level, compact, minimum 10 mm thick coat. Obtain the finish with a stainless steel floating trowel, wooden, sponge or plastic float.

*For ease of application and finish, avoid using AXEL 3000, ALGIREX or 751 LANKOLATEX in the top coat application of the trowel, float or sponge smooth finish. 

 

Documents