Product Data Sheet Show all documents

Parex® Parlumiere Moyen

REGULAR FINISH THROUGH COLOURED HYDRAULIC LIME RESTORATION TOP COAT, REPOINTING AND BEDDING MORTAR

Through-coloured top coat render made of hydraulic lime, used for the finishing coat of traditional renders, for repointing works or as a bedding mortar for brickwork, stone and other suitable masonry.

  • Lime Render
  • Bedding Mortar
Product Data Sheet Show all documents

Usage

  • Lime Render
  • Bedding Mortar
 

Advantages

  • Lime Render
  • Bedding Mortar

Packaging

25 kg bags

Colour

•    Medium Scraped
•    Sponge or Float smoothed(1)
•    Spray Textured
•    Smooth Spray Textured
•    Brushed
For additional information refer to the data sheet on TEXTURED MINERAL FINISHES.

(1)The float/sponge smoothed finishes may
vary in appearance, particularly due to different factors such as the line and level and condition of the substrate or the appearance of a slurry finish caused by over floating the surface. The latter may produce some micro cracking effect on the render surface which may affect the aesthetical appearance but does not affect its durability.

Product Details

Product Information

Chemical Base

Binder: hydrated lime + hydraulic binder (lime/binder ratio > 74 % by volume)
Filler: calcareous and siliceous sand
Light mineral additives
Organic additives: less than 0.2 %
Mineral pigments

Shelf Life

12 Months from date of manufacture 

Storage Conditions

Dry frost free conditions

Maximum Grain Size

Particle size: 0–5.6 mm
Technical Information

Compressive Strength

CS I

Capillary Absorption

W0 

Reaction to Fire

A1 

Application

Application Information

Mixing Ratio

4.6 – 5.6 L per 25 kg bag
Application steps

EQUIPMENT

  • Manual application: stainless steel trowel/float.
  • Mechanical application:

MECHANICAL APPLICATION

SPRAY RENDER MACHINE

SPRAYING POT

Pump pressure

6 – 8 bars (water)

Air flow

60 m3 per hour minimum

Air pressure

4 – 6 bars

SUBSTRATE PREPARATION

  • Substrates must be clean, sound, dust-free and free of any material which may prevent adhesion.
  • Remove all traces of plaster, paint, etc. Construction of the masonry must comply with BS 8000-3.
  • On low suction substrates e.g. shuttered concrete or high suction substrates e.g. lightweight aircrete or clay blockwork, first apply a coat of ready-to use FIXOPIERRE or a PARLUMIERE FIN key coat made up by adding 0.5 L of FIXOPIERRE to the mixing water volume for 25 kg bag of PARLUMIERE FIN.
  • On wet or wet patchy substrates or where different materials have been used it is advisable to apply a key coat of FIXOPIERRE for the mixing volume for a 25 kg bag of FIXOPIERRE. Allow the key coat to fully dry a minimum of 48 hours before the application of the next coat.
  • TV10 MESH may also be required, dependent upon substrate condition and project specification.
  • Check soundness, remove all loose material e.g. paint, organic coverings, plaster. Clean cracks and fill with PARLUMIERE CLAIR or PAREXAL, at least 7 days prior to application of facing.
  • Spray with water the day before until saturated, but not so the wall is running with water. Repeat prior to application, ensuring that substrate is wet through.
  • Follow recommendations in BS EN 13914-

MIXING

  • Machine mixing time: 5 minutes
  • Cement mixer mixing time: 5 – 7 minutes

APPLICATION

On hardened/cured render coating – thickness 5 to 10 mm maximum.

  • Apply one compact coat in 1 or 2 layers (2nd layer whilst 1st is still fresh), depending on finish required.

On repaired hardened/cured render coating – thickness 10 to 12 mm maximum.

  • Apply in 2 coats.

For joints between bricks and facing stones.

  • Refill joints in one layer of 10 to 30 mm, compacting with a trowel.  Brush after drying.

Drying time before covering the following base coats.

  • PARLUMIERE CLAIR: 3 to 10 days.
  • PARLUMIERE STH: 7 days minimum.
  • PARINTER RENOVATION: 3 to 10 days.  

Documents