Sikafloor®-31 PurCem®

LEED Rating:

Conformity with LEED v2009 IEQc 4.2: Low-Emitting Materials - Paints and Coatings

• Synthetic resin screed material according to EN 13813:2002,Declaration of Performance 02 08 02 02 004 0 000001 1088, certified by notified factory production control certification body 0086, certificate of conformity of the factory production control 541325, and provided with the CE marking.
• Coating for surface protection of concrete according to EN 1504-2:2004, Synthetic resin screed material according to EN 13813:2002,Declaration of Performance 02 08 02 02 004 0 000001 1088, certified by notified factory production control certification body
  0086, certificate of conformity of the factory production control 541325, and provided with the CE marking.
• EN1186, EN 13130, and prCEN/TS 14234 standards, and the Decree on Consumer Goods, representing the conversion of directives 89/109/EEC, 90/128/EEC and 2002/72/EC for contact with food stuffs, according to test report by ISEGA, 32758 U11 and 32759 U11, both dated December 6th, 2011. (Tests performed on Sikafloor® -20/21/22/29 and 31 PurCem® in standard and LP versions).
• British Standards Specifications (BSS) acceptance for use in the UK.
• Campden and Chorleywood Food Research Association, Ref. S/REP/125424/1a and 2a, dated 8th February, 2012
• Fire classification report according to EN 13501-1 from Exova Warrington Fire for Sikafloor®-21 PurCem® No.31050, dated 24th of March, 2012
• Liquid water transmission rate test report from the Technology Centre, Ref. 15456 dated January 25th, 2012
• Impact resistance values tested at PRA, Ref. nº 75221-151, dated January 11th, 2012

The package must be stored properly in original, unopened and undamaged sealed packaging, in dry conditions at temperatures between +5°C and +30°C.

Part A+B+C mixed: ~ 1.25 kg/l ± 0.03 (at +20°C)

Part A : B : C = 1 : 1: 1.40 (packaging size = 1.50 : 1.50 : 2.10 ) by weight

Mix full units only.

+10°C min. / +40°C max.

85% max.

Beware of condensation!
The substrate and uncured floor must be at least 3°C above dew point to reduce the risk of condensation or blooming on the floor finish.

+10°C min. / +40ºC

Can be installed on substrates with higher moisture content. No ponding water. Check rising moisture. The substrate needs to be visibly dry and have adequate pull-off strength min 1.5 N/mm2.

Before overcoating Sikafloor®-31 PurCem® allow:

Times are approximate and will be affected be changing ambient and substrate conditions, particularly temperature and relative humidity.

~ 0.4 – 1.0 kg/m2 (depending on the system build-up)

Premix part A with a low speed electric stirrer and then add part B and mix for 30 seconds. For the colourpack version, premix part A neutral with a low speed electric stirrer and add part D to it. Mix until a uniform colour is achieved. Ad part B and mix for 30 seconds.

Use a double paddle (axis) mixer and gradually add part C (aggregate) to the mixed resin. Allow part C to blend for further 2 minutes minimum, to ensure complete mixing and a uniform moist mix is obtained. During the operations, scrape down the sides and bottom of the container with a flat or straight edge trowel at least once (parts A+B+C) to ensure complete mixing.

Mixing Tools
A low speed electric stirrer (300-400 r.p.m.) and an Exomixer-type mixing paddle suited to the size of the mixing container to minimise the air entrapment.

On smooth screeds apply the mixed Sikafloor®-31 PurCem® using a short or medium nap roller directly from a paint tray. On broadcasted screeds pour the material and spread it using a squeegee and then back-roll the excess using a medium knap roller.

Clean all tools and application equipment with Thinner C immediately after use. Hardened / cured material can only be mechanically removed.